AMF Catalogue ZERO-POINT SYSTEMS Page 10
Offre client commercial**Meilleures ventes de AMF Spannsysteme
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
faQs aBOut ZerO-pOint Clamps and the amf ZerO-pOint sYstem are suBjeCt tO the amf ZerO-pOint Clamping mOdule defined in standard din en isO 13849? > yes, the amF zero-point clamping modules in sizes kP, kH and Bm were designed using the fundamental and proven safety principles defined in en iSo 13849-2, table a.1 and a.2 or B.1 and B.2, or table c.1 and c.2. the user is obliged to comply with these safety principles during the implementation and operation of our products. what is pull-in fOrCe / hOlding fOrCe? the pull-in force describes the force with which the stud is pulled in and clamped with positive interlocking in the clamping > module. the holding force, in contrast, specifies the maximum permissible pull force of the engagement screw. what is repeataBilit Y? the repeatability specifies the tolerance range within which the recorded reference points on the workpiece lie after > removal and reclamping of the same workpiece. the repeatability, also called repetition accuracy, is below 0.005mm. what advantages result frOm the use Of ZerO-pOint, timing and undersiZe pull-studs? these different types of pull-studs offset the spacing tolerances of pull-studs and clamping modules. > the fixed reference point is achieved through the zero-point pull-stud; the slit pull-stud serves to compensate for the still-free axis. the under size pull-stud does not have a centring function, but only a clamping and holding function. Can i insert the pull-stud direCtlY intO the wOrkpieCe fOr maChine prOCessing? the high costs for chucking fixtures and workpiece clamping can be effectively saved here if the pull-studs are mounted > in the workpiece, which is clamped directly using the clamping modules. as a result, a complete 5-sided processing of the workpiece is possible in one chucking. With the different stud sizes (attaching thread m6 to m16), workpieces of different sizes can be clamped. hOw dOes the sYstem COmpensate fOr heat, suCh as frOm metal Cutting? > through the different pull-stud designs, the system can compensate for temperature differences between the workpiece and the clamping module easily and controllably. For a graphic depiction of the stud array, see page 124 of the catalogue. if you have other technical questions, please contact us at any time. Subject to technical alterations. 10 ZERO-POINT-SYSTEMS ANDREAS MAIER GmbH & Co. KG ∙ Phone: +49 711 5766-196 ∙ Web: www.amf.de
228 Pages | Valable jusqu’au 12/2025 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.