GEDORE Automotive KLANN Main catalog General Repairs Página 38
Oferta para clientes comerciales**Productos de la página del catálogo
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
Springs and Shock Absorbers KL-.... 1 KL-0145-120 A Supporting Device for Control Arm Universal application. The device is used in conjunction with a transmission jack for supporting control arms. The support takes place via the wheel hub, thus, ensuring the correct raising and lowering of control arms/axles to specified positions. An indispensable tool when removing and installing a suspension strut. KL-0040-2588 KL-0040-2588 Adaptor Sleeve, VW, Ø 36mm This adaptor is needed to use the retaining devices KL-0040-258 A and KL-0040-288, and the KL-0145-120 supporting device in conjunction with the VW transmission jacks having a retaining Ø of 36mm. Technical Data: Pin Ø: Retaining Ø: KL-0005 30mm 36mm KL-0005 Spring Compressor (Universal) Universally suitable for use on springs in which the spring pressure does not exceed 8,000N. The spindles feature contra-rotating threads which eliminate the risk of slipping. (Not suitable for use on Mercedes springs.) Note: Two-part spring compressors without a safety loop are not authorized for use in workshops. Technical Data: Max. load.: Span width (Jaw opening): 8,000N 65-320mm Accessories: KL-0005-1 Pair of spindles for level-lift suspensions (not shown) KL-0006-2 KL-0006-2 Spring Compressor (Universal) Allows compressing the spring in-situ on the vehicle, so that the strut can be removed without dismounting the steering knuckle/ stub axle. This is important on the front axle of VW vehicles and on the rear axle of Ford Mondeo, etc. Especially suitable for: • Suspension strut mount replacement, e.g. VW Golf (IV). Thanks to the spring compressor KL-0006-2, the suspension strut mount bearing can be replaced in situ on the vehicle within a few minutes without having to remove and re-install the suspension strut. Expenditure of time about 15 minutes; Time savings about 1 hour. • Spring and shock absorber unit removal and installation, e.g. VW Golf (IV) By using the spring compressor KL-0006-2, springs can be pre-compressed in situ on the vehicle without having to remove the steering knuckle/ stub axle. Spreader tool KL-0104-21-1 A is used to widen strut clamping bores, thus allowing the spring/shock absorber unit to be easily removed from the clamping bore hole. Expenditure of time about 10 minutes; Time savings about 30 minutes. The spindles are equipped with contra-rotating threads which eliminate the risk of slipping round the spring. (Not suitable for use on Mercedes springs.) Note: Use a spring compressor such as the KL-9002 or KL-5501 to remove the spring from the vehicle. Two-part spring compressors without safety loop are not authorized for use in workshops. Technical Data: Max. load capacity: Jaw opening: 1-32 (38) 8,000N 65-200mm Copyright GEDORE Automotive GmbH, Germany formerly
580 Páginas | Válido hasta 12/2025 | Página anterior | Página siguiente
Elija su idioma
Cuestiones jurídicas
El fabricante es el único responsable del contenido, el precio y los detalles de los productos y ofertas presentados en los catálogos. Sujeto a cambios técnicos y ópticos por parte del fabricante y a excepción de errores.
Formulario de pedido de productos especiales
El servicio de compras ToolTeam®
¿Busca productos que aparecen en el catálogo pero que no se pueden comprar directamente en línea?Nuestro servicio de compras estará encantado de hacerle una oferta individual y no vinculante.