BILZ - Spannsysteme Página 69
Oferta para clientes comerciales**Los mejores vendedores de BILZ WERKZEUGFABRIK
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
excluyendo el transporte
WFSL – Gewindeschneid-Schnellwechselfutter WFSL – Quick change tapping chucks WFSL – Bezeichnung/Id. Nr. Designation/Id. No. + WFSL60 6709939 WFSL60-IK 6709942 WFSL60/A4 6709940 WFSL60-IK/A4 6709943 WFSL100 6709945 WFSL100-IK 6709947 WFSL100/A4 6709946 max. Nm WEK 60 M30 – M120 1400 20 50 bar + – 20 d d2 I 125 72 257 60-IK X 60 1800 60-IK 100 X M48 – M200 2400 156 92 323 100-IK 100 X 3000 Längenausgleich einstellbar von Druck 0 mm / Zug 40 mm bzw. Druck 40 mm / Zug 0 mm. Einstellung ab Werk Druck 20 mm / Zug 20 mm. Einstellung siehe Seite 80 – 81 Length compensation adjustable from tension 0 mm / compression 40 mm bzw. tension 40 mm / compression 0 mm. Setting from factory tension 20 mm / compression 20 mm. Adjustment see page 82 – 83 Passende Schnellwechsel-Einsätze siehe Seite 79 Suitable quick change adaptors see page 79 Futterauswahl: – max. Gewindgröße / Steigung – Drehmoment aus dem Diagramm, Seite 82 – 84 ablesen – oder an Hand der Formel „Drehmoment“ berechnen – danach das Futter auswählen Chuck selection: – max. thread size /pitch – check torque in chart page 82 – 84 – or use formula “torque” for calculation – then choose chuck Beispiel Example nach Diagramm Seite 85 acc. chart page 85 M 76 x 6 = 1915 Nm für Material bis 1000 N / mm2 for material up to 1000 N / mm2 = WFSL 100 ... notwendig required nach Formel Seite 86 acc. formula page 86 M 76 x 6 für Material for material 6620, kc =1600 MD = 1600 x 62 x 76 x 2 = 1094 Nm für for 6620 8000 = WFSL 60 ... ausreichend adequate WFSL 66 Clamping Systems
186 Páginas | Válido hasta 07/2025 | Página anterior | Página siguiente
Elija su idioma
Cuestiones jurídicas
El fabricante es el único responsable del contenido, el precio y los detalles de los productos y ofertas presentados en los catálogos. Sujeto a cambios técnicos y ópticos por parte del fabricante y a excepción de errores.
Formulario de pedido de productos especiales
El servicio de compras ToolTeam®
¿Busca productos que aparecen en el catálogo pero que no se pueden comprar directamente en línea?Nuestro servicio de compras estará encantado de hacerle una oferta individual y no vinculante.
