Remko Air conditioning chilled water KWP 755 1703330

Chiller in modular design with heat pump function for outdoor installation, ready for connection, air-cooled.
Weather-resistant base frame with removable cladding panels made of powder-coated sheet steel, colour similar to RAL 9018. Condenser and sound-insulated compressor compartment separated from each other. Horizontal air inlet via large-area high-performance condenser (cooling mode) in straight design made of refrigeration copper pipe with form-fit aluminium fins. Vertical air outlet via aerodynamically optimised, statically and dynamically balanced axial fan(s) with protective cage. Standard operating limits in cooling mode between +45°C and +5°C, range can be extended down to -15°C 6) with winter pressure control accessory. Standard operating limits in heating mode between -10°C and +20°C. Two fully hermetic, vibration-damped scroll compressors with refrigerating machine oil filling, optimally controlled according to the operating times. One refrigerant circuit made of refrigeration copper pipe, hermetically sealed and pressure-tested at the factory, dried and filled with R 410 A safety refrigerant. Control option via Schrader valve. High and low pressure monitors, pressure transmitters on the high and low pressure side, filter dryer and thermostatic expansion valve with external pressure equalisation. Integrated four-way reversing valve for switching between cooling and heating mode. Evaporator as refrigerant-water heat exchanger in brazed plate design made of stainless steel, vapour diffusion-tight insulation, return temperature range from +18°C to +10°C in cooling mode and from +45°C to +20°C in heating mode. Insulated medium circuit for water-glycol mixtures made of steel pipe with filling and draining connection, manual air vent valve and differential pressure switch for monitoring the volume flow. Medium connections in imperial Vitaulic design.

Control box with terminal strip for mains supply, potential-free input for external release, potential-free output for collective fault signal and connection of a cable remote control. Fully wired and tested main and control circuit with phase sequence relay, circuit breaker, fuses, contactors for main and control circuits and transformers fitted as standard. Automatic restart after power failure.

Easily accessible microprocessor controller with RS485 and USB interface for independent monitoring and control of all operating functions, protected from environmental influences and based on Linux. User-friendly display of all control parameters and coded fault messages within a value and parameter display, e.g. medium inlet and outlet temperatures, operating pressures in the refrigeration circuit. Function display of the operating modes, fan, compressors, circulation pump and collective fault. Operation of the device using six operating buttons. Three password-protected parameter areas available. Compliance with all requirements of the Ecodesign Directive (EU) 813/2013. When planning and installing the appliances, the regional regulations and ordinances or environmental protection laws, e.g. WHG, must be taken into account.

Available as accessories:
Medium circuit with pump or storage tank and pump in various pressure levels
Glycol
Cable remote control
Frost protection heater
Condenser protection grille
Heat recovery, Partial capacity
Vibration damper
Winter control
Soft start
Electronic expansion valve
Manometer refrigeration circuit
Control cabinet heater
Technical unit handover

The units comply with the relevant EU regulations and are CE-marked in accordance with the applicable directives.

Technical performance data:
MakeREMKO
TypeKWP 755
Nominal cooling capacity, total 1) [kW]74.40
Nominal heating capacity 2) [kW]91.80
Energy efficiency ratio cooling EER 1)2.51
Energy efficiency ratio heating COP 2)3.84
Setting range, return temperature cooling [°C]+10 to +18
Setting range, Return temperature, heating [°C]+30 to +45
Working range, cooling 6)/heating [°C]-15 to +45/-10 to +20
Capacity grading0/50/100
Refrigerant 7)R 410 A
Compressor, number/type2/Scroll
Fan, number2
Air flow rate, max. [m³/h]43600
Sound pressure level, max. 3) [dB(A)]53.6
Sound power level [dB(A)]85.6
Voltage supply [V/~/Hz]400/3/50
Protection classIP 24
Electrical power consumption max. 4) [kW]45.59
Electrical power consumption max. 4) [A]65.87
Electr. rated power consumption cooling1) [kW]29.62
Electr. rated current consumption cooling 1) [A]45.05
Electr. rated power consumption heating 2) [kW]23.91
Electr. rated current consumption heating 2) [A]36.00
Electr. starting current, max. LRA [A]172.50
Nominal volume flow, medium cooling [m³/h]12.82
Nominal pressure losses, internal cooling [kPa]25.4
Medium connections2 ‘
Minimum medium volume system [l]370.0
Dimensions (H/W/D) [mm]1954/1123/3005
Weight [kg]751.2
Operating weight approx. [kg]759.6

1) Air inlet 35°C, medium temperatures 7/12°C, 0% glycol
2) Air inlet 7°C, medium temperatures 35/30°C, 0% glycol
3) Distance 10 m free field
4) Air inlet 45°C, medium temperatures 18/15°C, 0% glycol
6) Only with winter pressure control accessory
7) Contains greenhouse gas according to Kyoto protocol