Pneumax - Hauptkatalog Page 883
Commercial customer offer**Top sellers from Pneumax GmbH
Compact cylinders according to standard ISO 21287 Series 1500 Ecompact Series 1500 - Compact cylinders according to standard ISO 21287 “ECOMPACT” General These cylinders are built according to ISO 21287 standards. New barrel profile has two sensor slots on the three sides (Ø20 and Ø25 one slot) suitable for sensors 1580._, MRS._, MHS._ series housing, without need for adaptors. Versions with end stroke adjustable pneumatic cushioning are also available, allowing adjustments to deceleration and keeping the required overall dimensions according to ISO 21287. For fixing operation is possible to use the four threaded holes on the end covers, or screws in body holes, alternatively all the fixing devices of UNITOP RU-P/6-P/7 (Ø20 and Ø25) and ISO 15552 (from Ø32 to Ø100) series. Construction characteristics Body anodised aluminium End cap aluminium alloy casting painted Bearing piston rod sintered bronze from Ø20 to Ø25 stainless steel Piston rod from Ø32 to Ø100 C43 chromed (on request stainless steel) from Ø20 to Ø40 acetal resin (aluminium on request), Ø50 and Ø100 Piston aluminium (with FPM seals, aluminium piston for all standard diameters) Standard: NBR oil resistant rubber , PUR piston rod seals Seals (PUR or FPM seals available upon request) Spring stainless steel Fixing screws plated zinc steel 3 Filtered air. Fluid No lubrication needed, if applied it shall be continuous. 10 bar Max. pressure -5°C - +70°C with standard seals (magnetic or non magnetic piston) -30°C - +80°C with PUR seals (magnetic or non magnetic piston) Operating temperature -5°C - +80°C with FPM seals (magnetic piston) -5°C - +150°C with FPM seals (non magnetic piston) Please follow the suggestions below to ensure a long life for these cylinders: •use clean and lubricated air •correct alignment during assembly with regard to the applied load so as to avoid radial components or bending the rod. •avoid high speeds together with long strokes and heavy loads: this would produce kinetic energy which the cylinder cannot absorb, especially if used as a limit stop (in this case use mechanical stop device and aluminium piston) •evaluate the environmental characteristics of cylinder used (high temperature, hard atmosphere, dust, humidity etc.) Please note: air must be dried for applications with lower temperature. Use hydraulic oils H class (ISO VG32) for correct continued lubrication. Our Technical Department will be glad to help. Stroke tolerance, minimum and maximum spring loads and cushioning length Bore (mm) Ø20 Stroke tolerance (mm) +1.5 / 0 mm Ø25 Ø32 Ø40 +2 / 0 mm Ø50 Ø63 Ø80 Ø100 +2.5 / 0mm Minimum and maximum springs load (N) Cushioning length (mm) min. max. 10.8 19.6 / 16.7 22.6 5 19.6 25.5 6.5 25.5 42.2 8 44.1 96.3 7.5 44.1 96.3 7.5 63.8 100.1 8 107.9 193.3 12 Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice 3 | 87 Pneumatic actuatiOn Operational characteristics
1106 Pages | Valid until 06/2025 | Previous page | Next page
Choose your language
Legal issues
The manufacturer is exclusively responsible for the content, price and article details of the products and offers presented in the catalogues. Subject to technical and optical changes by the manufacturer and errors excepted.
Request form for special products
The ToolTeam® Procurement Service
Are you looking for products that are shown in the catalogue but cannot be purchased directly online?Our procurement service will be pleased to make you a non-binding and individual offer.