CELO main catalog Page 103
Commercial customer offer**Top sellers from CELO Befestigungssysteme GmbH
CELO Monting in concrete L dk h e ef = 3x 1. Drill a hole: Drill hole depth + insulation $WWDFKWKHPL[LQJQR]]OHH[WHQVLRQ0'9WRWKH 3. Cut the ResiTHERM® 16 or 12 to length: thickness After determining the correct length, cut the threaded rod to length with a metal saw or similar. PL[LQJQR]]OH0' Squeeze out the injection mortar until the mortar has DXQLIRUPJUH\PL[LQJFRORXUGLVFDUGWKH pre-run of the first at least 3 strokes. VY 300SF 6 5 4 °C Resi 2. Clean the drill hole properly according to ETA: [EORZ[EUXVK[EORZ 5. Fill at least 2/3 of the drill hole with composite mortar (start from the beginning). For number of 6. Screw in the ResiTHERM®RUZLWKWKHKH[DJRQ 7. Observe curing time of the injection system, see bit (included) and a cordless screwdriver until the seal cartridge label of the ResiFIX injection mortar. strockes see mounting instructions at www.celofixings.com. Important: Follow the installation instructions and is pressed against the plaster. Note: The thermal separation module drills itself through the insulation (additional sealing is not processing time of the ResiFIX injection mortar used in accordance with the approval/assessment. necessary, unless the plaster is very rough) 8. Afterwards, the attachment can be mounted, PD[WRUTXH7inst = 25 Nm (ResiTHERM® 16) or 19 Nm (ResiTHERM® 12) Mounting in masonry (hollow brick) Ldk 125 mm 1. Drill a hole: Drill hole diameter = 20 mm. e 4. Enlarge the opening in the plaster for the collar of the 3. Cut the ResiTHERM® 16 or 12 to length: 'ULOOKROHGHSWK͡PPLQVXODWLRQWKLFNQHVV LQFO Correct length LdK: Anchorage depth in plastic sleeve (125 mm) + insulation thickness e (incl. plaster) plaster). Observe the drilling procedure of the approval/ assessment of ResiFIX injection mortar. Perforated bricks and aerated concrete: Rotary After determining the correct length, cut the threaded rod to length with a metal saw or similar. plastic sleeve to 26 mm. To do this, briefly screw the thermal separation module in and out through the SODVWHUIRURQO\DSSUR[WKUHDGWXUQVRUUHDPWKH plaster with a drill or drill with a bigger 26 mm drill. 5. Push the plastic sleeve into the drill hole with the help of a folding ruler or similar. VY 300SF 6 4 5 Resi drilling - without impact 2. Clean the drill hole properly according to ETA: [EORZ[EUXVK[EORZ = 3x $WWDFKWKHPL[LQJQR]]OHH[WHQVLRQ0'9WRWKH 7. Fill the plastic sleeve completely with composite PL[LQJQR]]OH0' Squeeze out the injection mortar until the mortar has mortar (start from the beginning). For number of strockes see mounting instructions at DXQLIRUPJUH\PL[LQJFRORXUGLVFDUGWKH pre-run of the first at least 3 strokes. www.celofixings.com Important: Follow the installation instructions and processing time of the ResiFIX injection mortar used in accordance with the approval/assessment. 8. Screw in the ResiTHERM®RUZLWKWKHKH[DJRQ bit (included) and a cordless screwdriver until the seal is pressed against the plaster. Note: The thermal separation module drills itself 102 through the insulation (additional sealing is not necessary, unless the plaster is very rough) 9. Observe curing time of the injection system, see cartridge label of the ResiFIX injection mortar. 10. Afterwards, the attachment can be mounted, PD[WRUTXH7inst = 25 Nm (ResiTHERM® 16) or 19 Nm (ResiTHERM® 12)
316 Pages | Valid until 03/2023 | Previous page | Next page
Choose your language
Legal issues
The manufacturer is exclusively responsible for the content, price and article details of the products and offers presented in the catalogues. Subject to technical and optical changes by the manufacturer and errors excepted.
Request form for special products
The ToolTeam® Procurement Service
Are you looking for products that are shown in the catalogue but cannot be purchased directly online?Our procurement service will be pleased to make you a non-binding and individual offer.