Albrecht Katalog Präzisions-Spannfutter Seite 38
Gewerbekunden Angebot**Topseller von Albrecht
zzgl. Versand
zzgl. Versand
zzgl. Versand
zzgl. Versand
zzgl. Versand
alues. sured ic modal elated ell dynamic ools penhus onxhibited xpanxpandynamic adisek hanging mal or xire aritudied. o 74 Table 1 Main properties of the investigated tool holders Fig. 1 Examples of the investigated tool holder systems Investigated tool holder systems: o spindle-side aces to ted ial capable to hout al. aces on ed el- Full-periphery clamping Point-line clamping b 80 Weldon a 90 TS 1120 918 1457 1274 1123 [g] [mm] 92 100 90 mass m A APC ER HE Tool holder 42 24 40 42 32 [mm] D1 15 8 18 12.5 9 [mm] bm Monolithic b Monolithic a Monolithic a Modular Modular Design MC12 by Gebr. Heller torus cutter, D=12, number of teeth=4 Steel, 42CrMo4 (1.7225) Cutting Parameter: n= 3979 rev/min fz= 0,04 mm/rev/tooth ae= 7mm ap= 18mm Machine: Tool: Material: Test setup: Keywords Tool holders · Dynamic behaviour · Surface formation · Frequency analysis · Shaft tools · Steel milling Abstract Tool holders are an important power train component of milling with shaft tools having a high impact on dynamic process behaviour and process results. This leads to a significant demand among industrial companies for scientifically proven methods to analyse tool holders which are easy to use as well. Different approaches were applied in order to meet these demands. The dynamic vibrational behaviour of different clamping mechanisms is investigated using tool holders of similar dimensions. First, the resonance frequencies of the tool holders are identified from dynamic compliance measurements in the machine tool. Subsequently, the dynamic process behaviour is investigated by peripheral milling tests in which vibrations of tool and tool holder are detected by acceleration sensors and microphones. Analysis of the sensor data and optical analysis of the manufactured surface reveal a significant influence of the particular clamping mechanism, superimposed by certain geometrical variations of the investigated tool holders. Chatter frequencies occurring during milling tests seem independent of the clamping mechanism respectively the particular tool holder and are caused by the tool or machine-tool components. They correspond roughly with the natural frequencies identified before. Chatter intensity and spindle speeds, at which chatter occurs, are influenced by the tool holders. The occurrence of chatter vibrations correlates with a significant drop in the surface quality of the workpiece. High resonance frequencies of the tool holder excited by chatter and low-frequency waviness observed on the machined surface are related. The well-known phenomenon can be explained under rough milling conditions by a 2D-model-based superposition of subsequent cutting edge engagements. This in turn may enable dynamic analysis and optimisation of rough milling operations by easy to use shop floor equipment in future. Assessment of tool holder performance in roughing with end mills and surface quality. (Tool holder: ER-collet, n = 2708 − 5250 rev/min, Rosenthal O. / Hintze W. / Möller C. (Published 08.01.2020 https://doi.org/10.1007/s11740-019-00944-w . Assessment of tool holder performance in roughing with end mills. Institute of Production Management and Technology, Hamburg University of Technology. Springer Nature) Fig. 6 Visualisation of in-process vibrations using Campbell diagrams based on acceleration sensor data. ( n = 2708 − 5250 rev/min, fz = 0.04 mm/rev/tooth, ae = 7 mm , ap = 18 mm) 75 ocess vibrations using Campbell diagrams based on acceleration sensor dat APC with best results in comparison to other tool-holders: Fig. 7 Correlation between in-process vibrations fz = 0.04 mm/rev/tooth, ae = 7 mm , ap = 18 mm) Correlation between in-process vibrations and surface quality: Siege haben Gründe
39 Seiten | Gültig bis 12/2021 | Vorherige Seite | Nächste Seite
Sprache wählen
Rechtliches
Ausschließlich verantwortlich für Inhalt, Preis- und Artikelangaben der dargestellten Produkte und Angebote innerhalb der Kataloge ist der Hersteller. Technische und optische Änderungen des Herstellers und Irrtümer vorbehalten.
Anfrageformular für spezielle Produkte
Der ToolTeam® Beschaffungsservice
Sie suchen Produkte die im Katalog abgebildet, aber online nicht direkt kaufbar sind?Unser Beschaffungs-Service macht Ihnen gerne ein unverbindliches und individuelles Angebot.