Pneumax - Hauptkatalog Side 650
Kommercielt kundetilbud **Top-sælgere fra Pneumax GmbH
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
ekskl. forsendelsesomkostninger
Air service units Series Airplus Operational characteristics Construction characteristics Body Operatore Solenoide Rear end cap Spool Spool seals Piston Spring Electrical Interface AIR TREATMENT 2 Aluminium Technopolymer Aluminium Aluminium Polyurethane Aluminium EN 10270-1 DH steel Male MP12 4 PIN TYPE A connector Fluid Working temperature Minimum working pressure Maximum working pressure Filtered air. No lubrication needed, if applied it shall be continuous. -10°C +50°C 2,5 bar 10 bar ASSEMBLY AND INSTALLATION: Undertake the installation respecting the safety requirements with regards to the system and components for hydraulic and pneumatic transmissions. Install the device as close as possible to the point of use. Its assembly is possible in any position. Pay attention to the flow direction, indicated on the main body with the labels IN and OUT. During the components discharge, high levels of noise occur. The use of a silencer on the discharge port is recommended. Ensure there is sufficient space for assembly during the installation process. Please ensure that the discharge area is always clear, and in case a silencer is used, periodically verify that it is not obstructed. It is possible to integrate and install the device in an existing AIRPLUS group or in a new installation, or else to use the device individually attaching it by aligning the assembled unit with the relevant fastening flange for the supply and discharge valve, or to use the device individually attaching it by aligning the assembled unit with the type “Y” fastening flange for the double supply and discharge valve. WARNING! Pay particular attention to external factors such as the nearness of live wires, magnetic fields, metallic objects providing magnetic conduction very close to the device, which may influence and disturb the diagnostic system. WARNING! The electrical connection must be made exclusively by specialized personnel, using components that have no voltage present. Only use power supplies which can guarantee a safe electrical isolation of the working voltage in accordance to IEC/EN 60204-1. Additionally, observe the requirements anticipated by the PELV circuits in accordance to IEC/EN 60204-1. CARE AND MAINTENANCE WARNING! Do not connect or disconnect the device when energised! Do not open and/or disassemble the parts that are included in the energised valve. Once the power supply is disconnected, wait for a few minutes before opening or disassembling parts of the valve that result in its disassembly. Before carrying out any operation, it is essential to remove the pneumatic and power supply to the device and wait for the residual pressure to be completely discharged. Please ensure that the discharge is always clear, and in case a silencer is used, periodically verify that it is not obstructed. Periodically remove any dust deposits from the valve using a damp cloth. Use soapy water to clean the device. Do not use corrosive or alcohol-based products. For maintenance operations on internal components, please consult with PNEUMAX SPA. 2 | 76 Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice
1106 Sider | Gyldig indtil 06/2025 | Previous page | Næste side
Vælg dit sprog
Juridiske oplysninger
Producenten er kun ansvarlig for indhold, pris og artikeldetaljer for produkterne og tilbuddene i katalogerne. Med forbehold for tekniske og optiske ændringer og fejl fra producentens side.
Anmodningsskema til specialprodukter
ToolTeam® indkøbsservice
Leder du efter produkter, der er vist i kataloget, men ikke kan købes direkte online?Vores indkøbstjeneste vil med glæde give dig et uforpligtende og individuelt tilbud.
