Vigor V1757 Betriebsanleitung Batterie-Tester ViGOR1757 Strana 13
Nabídka komerčních zákazníků **Nejlépe prodávané z Vigor
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
3 Design and Function 3. Application Battery Voltage Test • Connect the clamps to the battery. Do not actuate the load switch. Battery voltage is shown in the display, without actuating the switch. • If the battery voltage is below 12.3V or above 13.2V the load can not be tested. If the load test is made all the same, “c.b.” (charge battery) will be shown on the display. • If the battery voltage is below 12.3V, please fully charge the battery before testing. After charging please wait 15 to 30 minutes before repeating the voltage test. If the reading is still below 12.3V and “c.b.” is indicated in the display, the battery should be replaced immediately. • If the battery voltage is above 13.2V, please check if the battery has just been charged. If so, please wait 15 to 30 minutes before starting a further voltage test. Battery Load Test • Connect the clamps to the battery. Battery voltage is shown in the display. • Press and hold the load switch for 10 seconds. Thus, internal load resistance is connected in and the battery is loaded with 100 ampere. This is about the electricity consumption of a medium-sized vehicle with common equipment (~1,200 W). Due to load the battery tester heats up. Do not press the load switch longer than 10 seconds. After finishing the load test the battery tester has to cool down for at least 5 minutes. Meaning of the test results – after 10 seconds of load: GREEN LED LIGHT: Battery capacity is good. Determine acid density of the battery with suitable tester. If necessary recharge battery. GREEN / YELLOW LED LIGHT Battery capacity is unsatisfactory. Battery may be either defective or discharged. Determine acid density of the battery with suitable tester. Recharge battery and re-test. RED LED LIGHT Battery may be defective, e.g. a bad cell or discharged. Release load switch. Determine acid density of the battery with suitable tester. Recharge battery and re-test. Testing the charging System 1. Connect the negative (black) clamp to the negative (NEG, N, -) battery terminal and the positive (red) clamp to the positive (POS, P, +) battery terminal. Press the load switch (ENTER). “TEST STATE – CHARGING AND LED LIGHT” will light up. 2. Start the engine and allow it to reach normal operating temperature. 3. Run engine at 1200 to 1500 rpm. cAUTIOn : Stay clear of moving engine parts. 4. Read the voltmeter. A reading with the red LED lighted up indicates a problem in the charging system that adds to undercharging (less than 13.6 V) or overcharging the battery (over 14.8 V). (Follow vehicle manufacturer’s instructions). Please refer to voltmeter and display test results. 13
16 Stránky | Platí do 12/2022 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.