Pneumax - Hauptkatalog Strana 867
Nabídka komerčních zákazníků **Nejlépe prodávané z Pneumax GmbH
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Cylinders according to standard ISO 15552 Series AISI 316 stainless steel Series AISI 316 stainless steel - Steel line General The 1393-1394 stainless steel ISO 15552 cylinders series are designed for corrosion resistance application such as marine, pharmaceutical and food ambiences. The pre lubrication grease used is NSF H1 certified for food application. Specific care has been taken during the design stages and the result is a clean profile cylinder easy to clean and free from possible residue build-up areas. All parts in contact with the external environment are in Stainless steel 316L and the seals are available in two different compounds for different temperature applications: PUR -30C° - +80 C° and FPM -5°C - +150°C. The range starts from 32 bore up to 100 bore , round barrel and tie rods design. Double acting version standard or with through rod, magnetic or not magnetic piston available. The piston is aluminium and the sensor bracket, when required is in stainless steel 316. The cylinder can be fixed via the threaded holes in the tie rod nuts or with the wide range of stainless steel accessories. Construction characteristics End caps, piston rod, barrel, cushion screws Stainless steel AISI 316 Rod-guide bushings Stainless steel AISI 316 with P.T.F.E. coat Half-pistons Aluminium Seals PUR or FPM on request Lubricating grease NSF-H1 certified grease for incidental contact with food Operational characteristics Filtered air. Fluid No lubrication needed, if applied it shall be continuous. Max. pressure 10 bar Operating temperature -30° C - +80°C with PUR seals -5° C - +150°C with FPM seals and non magnetic piston -5° C - +80°C with FPM seals and magnetic piston Bore Ø 32 - 40 - 50 - 63 - 80 - 100 Cushioning lenght mm 20 - 20 - 22 - 22 - 32 - 32 Please follow the suggestions below to ensure a long life for these cylinders: •use clean and lubricated air •correct alignment during assembly with regard to the applied load so as to avoid radial components or bending the rod. •avoid high speeds together with long strokes and heavy loads: this would produce kinetic energy which the cylinder cannot absorb, especially if used as a limit stop (in this case use mechanical stop device) •evaluate the environmental characteristics of cylinder used (high temperature, hard atmosphere, dust, humidity etc.) Please note: air must be dried for applications with lower temperature. Our Technical Department will be glad to help. Standard strokes (for all diameters) Stroke tolerance (ISO 15552) Bore from 0 to 150, every 25 mm 32 - 40 - 50 over 150 up to 500, every 50 mm over 500 up to 1000, every 100 63 - 80 - 100 Stroke up to 500 over 500 up to 1250 up to 500 over 500 up to 1250 Tolerance +2 0 +3.2 0 +2.5 0 +4 0 On request are available strokes up to 2800 mm Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice 3 | 71 Pneumatic actuatiOn 3
1106 Stránky | Platí do 06/2025 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.