Pneumax - Hauptkatalog Strana 836
Nabídka komerčních zákazníků **Nejlépe prodávané z Pneumax GmbH
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Cylinders according to standard ISO 15552 Series 1319 - 1320 - 1321 Series 1319-1320-1321 General This series of pneumatic cylinders is manufactured according to ISO 6431 standards adapted to VDMA 24562 and CNOMO/AFNOR 49003 that guarantee the interchangeability of the cylinders even without mounted anchoring. Construction characteristics from Ø32 to Ø125: UNI 5079 aluminium alloy casting painted black by cataphoresis from Ø160 to Ø200: UNI 3051 aluminium chilled painted black by cataphoresis End caps 3 Rod stainless steel or C43 chromed steel Barrel oxidised aluminium Cushion bushings hardened aluminium Rod-guide bushing self-lubricating sintered bronze Piston vulcanized rubber block on steel core with incorporated plastoferrite permanent magnet, or without magnet for non magnetic version (plus rear spacer). Seals standard: NBR Oil resistant rubber, PUR Piston rod and cushion seals (FPM seals available upon request) Cushion adjustment screws brass Pneumatic actuatiOn Operational characteristics Fluid Pressure Operating temperature Cushioning length Filtered air. No lubrication needed, if applied it shall be continuous. max. 10 bar -5 °C - +70 °C with standard seals (magnetic or non magnetic piston) -5 °C - +80 °C with FPM seals for 1319 and 1320 series (magnetic piston) -5 °C - +150 °C with FPM seals for 1321 series (non magnetic piston) Ø 32 - 40 - 50 - 63 - 80 - 100 - 125 - 160 - 200 mm 28 - 32 - 32 - 40 - 44 - 50 - 55 - 55 - 55 Please follow the suggestions below to ensure a long life for these cylinders: •use clean and lubricated air •correct alignment during assembly with regard to the applied load so as to avoid radial components or bending the rod. •avoid high speeds together with long strokes and heavy loads: this would produce kinetic energy which the cylinder cannot absorb, especially if used as a limit stop (in this case use mechanical stop device) •evaluate the environmental characteristics of cylinder used (high temperature, hard atmosphere, dust, humidity etc.) Please note: air must be dried for applications with lower temperature. Use hydraulic oils H class (ISO VG32) for correct continued lubrication. Our Technical Department will be glad to help. Stroke tolerance (ISO 15552) Standard strokes (for all diameters) Double acting version Stroke Bore from 0 to150, every 25 mm 32 - 40 - 50 up to 500 over 500 up to 1250 63 - 80 - 100 up to 500 over 500 up to 1250 over 150 up to 500, every 50 mm over 500 up to 1000, every 100 mm 125 - 160 - 200 On request are available strokes up to 2800 mm Single acting version From Ø32 to Ø125, up to stroke 50 mm On request are available strokes up to 200 mm up to 500 over 500 up to 1250 Minimum and maximum springs load for single acting version Bore 3 | 40 Ø32 Ø40 Ø50 - Ø63 Ø80 - Ø100 Ø125 Min. load (N) 15 25 50 100 150 Max. load (N) 40 80 115 200 250 Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice Tolerance +2 0 +3,2 0 +2,5 0 +4 0 +4 0 +5 0
1106 Stránky | Platí do 06/2025 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.