Pneumax - Hauptkatalog Strana 826
Nabídka komerčních zákazníků **Nejlépe prodávané z Pneumax GmbH
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Cylinders CNOMO-CETOP-ISO Series 1303 - 1304 - 1305 - 1306 - 1307 - 1308 Series 1303-1304-1305-1306-1307-1308 General They conform to CNOMO standards, fully complying with CETOP and ISO standards, with mounted fixing devices 32 to 100. Construction characteristic 3 End caps solid aluminium bar up to Ø100, alloy aluminium from Ø125 to Ø200 Rod C43 chromed steel, by thickness or stainless steel Barrel oxidised aluminium Tie rods steel with rolled threads Cushion bearings aluminium Rod-guide bushing brass (Ø32, 40, 50) in aluminium with self-lubricating bearings in sinterized bronze for the remaining BOREs Piston aluminium lathed from bar Seals Standard: NBR Oil resistant rubber, PUR Piston rod seals (FPM seals available upon request) Pneumatic actuatiOn Operational characteristics Fluid filtered and lubricated air - hydraulic oil (with special bushing) Pressure max. 12 bar (air) - 20 bar (oil) Operating temperature -5 °C - +70 °C with 1303-1308 standard seals -5 °C - +80 °C with FPM seals for 1306-1308 series (magnetic piston) -5 °C - +150 °C with FPM seals for 1303-1305 series (non magnetic piston) Cushioning length Ø 32 - 40 - 50 - 63 - 80 - 100 - 125 - 160 - 200 mm 20 - 20 - 22 - 24 - 24 - 25 - 27 - 35 - 35 Please follow the suggestions below to ensure a long life for these cylinders: •use clean and lubricated air •correct alignment during assembly with regard to the applied load so as to avoid radial components or bending the rod. •avoid high speeds together with long strokes and heavy loads: this would produce kinetic energy which the cylinder cannot absorb, especially if used as a limit stop (in this case use mechanical stop device) •evaluate the environmental characteristics of cylinder used (high temperature, hard atmosphere, dust, humidity etc.) Please note: air must be dried for applications with lower temperature. Use hydraulic oils H class (ISO VG32) for correct continued lubrication. Our Technical Department will be glad to help. Standard strokes Double acting version From 0 to 150 every 25 mm; from 150 to 500 every 50 mm; from 500 to 1000 every 100 mm (for all bores) On request are available strokes up to 2800 mm Single acting version up to stroke 50 mm Minimum and maximum springs load for single acting version Bore 3 | 30 Ø32 Ø40 - Ø50 Ø63 Ø80 - Ø100 Min. load (N) 20 25 50 100 Max. load (N) 55 80 115 200 Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice
1106 Stránky | Platí do 06/2025 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.