Pneumax - Hauptkatalog Strana 800
Nabídka komerčních zákazníků **Nejlépe prodávané z Pneumax GmbH
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Microbore cylinders according to standard ISO 6432 Series 1200 Rolled end covers "MIR" Series 1200, Rolled end covers “MIR” Construction characteristics End caps hard anodised aluminium Barrel stainless steel AISI 304 Piston rod stainless steel Piston brass (ø8-10-12) aluminium (ø16-20-25) Seals Standard: NBR Oil resistant rubber, PUR Piston rod seals (HNBR or FPM seals available upon request) Mounting steel painted in cataphoresis Forks zinc plated steel Single-acting springs C98 zinc plated steel for springs Cushioning length ø mm 16 - 20 - 25 - 32 15 - 18 - 18 - 18 Operational characteristics 3 Fluid Filtered air. No lubrication needed, if applied it shall be continuous. Maximum working pressure 10 bar Working temperature -5°C - +70°C with standard seals magnetic or non magnetic piston Pneumatic actuatiOn -5°C - +80°C with FPM seals magnetic piston -5°C - +80°C with HNBR seals magnetic piston -5°C - +120°C with HNBR seals non magnetic piston -5°C - +150°C with FPM seals non magnetic piston Please follow the suggestions below to ensure a long life for these cylinders: •use clean and lubricated air •correct alignment during assembly with regard to the applied load so as to avoid radial components or bending the rod. •avoid high speeds together with long strokes and heavy loads: this would produce kinetic energy which the cylinder cannot absorb, especially if used as a limit stop (in this case use mechanical stop device) •evaluate the environmental characteristics of cylinder used (high temperature, hard atmosphere, dust, humidity etc.) Please note: air must be dried for applications with lower temperature. Use hydraulic oils H class (ISO VG32) for correct continued lubrication. Our Technical Department will be glad to help. Standard strokes Double acting version Ø8 - Ø10 : 15 - 25 - 50 - 75 - 80 - 100 mm Ø12 - Ø16 : 15 - 25 - 50 - 75 - 80 - 100 - 150 - 160 - 200 - 250 - 300 mm Ø20 - Ø25 : 15 - 25 - 50 - 75 - 80 - 100 - 150 - 160 - 200 - 250 - 300 - 320 - 350 - 400 mm Ø32 : 15 - 25 - 50 - 75 - 80 - 100 - 150 - 160 - 200 - 250 - 300 - 320 - 350 - 400 - 450 - 500 mm On request are available strokes up to: Ø8 - Ø10 : 250 mm Ø12 - Ø16 : 700 mm Ø20 - Ø32 : 1000 mm Single acting version Front spring Ø8 - Ø32 : up to stroke 50 mm Rear spring Ø16 - Ø32 : up to stroke 50 mm Minimum and maximum springs load for single acting version 3|4 Bore Ø8 Ø10 Ø12 Ø16 Ø20 Ø25 Min. load (N) 2.2 2.2 4 7.5 11 16.5 23 Max. load (N) 4.2 4.2 8.7 21 22 30.7 52.5 Ø32 Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice
1106 Stránky | Platí do 06/2025 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.