Pneumax - Hauptkatalog Strana 758
Nabídka komerčních zákazníků **Nejlépe prodávané z Pneumax GmbH
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Proportional technology Series 1700 Electronic proportional regulator - Sizes 0 - 1 - 3 Installation/Operation PNEUMATIC CONNECTION The compressed air is connected by means of M5 threaded holes (for size 0 regulators), G 1/4” threaded holes (for size 1 regulators) and G 1/2” threaded holes (for size 3 regulators) on the body. Before making the connections, eliminate any impurities in the connecting pipes to prevent chippings or dust entering the unit. Do not supply the circuit with more than 10 bar pressure and make sure that the compressed air is dried (excessive condensate could cause the appliance to malfunction) and filtered at 5 micron. The supply pressure to the regulator must always be at least 1 bar greater than the desired outlet pressure. If a silencer is applied to the discharge path the unit response time may change; periodically check that the silencer is not blocked and replace it if necessary. ELECTRICAL CONNECTION For the electrical connection a SUB-D 15-pole female or a M12 connector is used (accordingly to the model, to be ordered separately). Wire in accordance with the wiring diagram shown below. Warning: INCORRECT CONNECTIONS MAY DAMAGE THE DEVICE Air Service UnitS 2 NOTES ON OPERATION If the electric supply is interrupted, the outlet pressure is maintained at the set value. However, maintaining the exact value cannot be ensured as it is impossible to operate the solenoid valves. In order to discharge the circuit downstream, zero the reference, make sure that the display shows a pressure value equal to zero and then disconnect the electric power supply. A version of the device is available that exhausts the downstream circuit when the power supply is removed. (Option “A” at the end of the ordering code). If the compressed-air supply is suspended and the electric power supply is maintained a whirring will be heard that is due to the solenoid valves; an operating parameter can be activated (P18) that triggers the regulator protection whenever the requested pressure is not reached within 4 seconds of the reference signal being sent. In this case the system will intervene to interrupt the control of the solenoid valves. Every twenty seconds, the unit will start the reset procedure until standard operating conditions have been restored. "521" Standard version with D-SUB connector "521" M12 BASIC and Standard versions TOP VIEW OF THE REGULATOR CONNECTOR 1 CONNECTOR PINOUT: 1 = DIGITAL INPUT 1 2 = DIGITAL INPUT 2 3 = DIGITAL INPUT 3 4 = DIGITAL INPUT 4 5 = DIGITAL INPUT 5 6 = DIGITAL INPUT 6 7 = DIGITAL INPUT 7 15 = ANALOG INPUT / DIGITAL INPUT 8 = SUPPLY (24 VDC) = DIGITAL OUTPUT (24 VDC PNP) = ANALOG OUTPUT (CURRENT) = ANALOG OUTPUT (VOLTAGE) = Rx RS-232 = Tx RS-232 = GND 9 10 11 12 13 14 15 TOP VIEW OF THE REGULATOR CONNECTOR 1 8 9 15 ® "521" CANopen version with M12 connector 5 2 4 1 M12 5P FEMALE 2 | 184 1 2 M12 4P MALE M12 BASIC version CONNECTOR PINOUT: 1 = POWER SUPPLY (24 VDC) 2 = NC 3 = GND 4 = ANALOG INPUT "521" CANopen® version with D-SUB connector 3 3 8 9 8 4 4 3 1 2 M12 Standard version CONNECTOR PINOUT: 1 = POWER SUPPLY (24 VDC) 2 = ANALOG OUTPUT (depending on the model) 3 = GND 4 = ANALOG INPUT "521 IO-Link version" CONNECTOR PINOUT: 1 = CAN_SHIELD 2 = CAN_V+ 3 = CAN_GND 4 = CAN_H 5 = CAN_L 6 = NC 7 = NC 8 = NC 9 = SUPPLY (+24 VDC) 10 = CAN_SHIELD 11 = CAN_V+ 12 = CAN_GND 13 = CAN_H 14 = CAN_L 15 = GND 5 4 1 2 M12 5P MALE CONNECTOR PINOUT: 1 = L+ 2 = +24 VDC (P24) 3 = L4 = C/Q 5 = GND (N24) M12 4P MALE Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice 3
1106 Stránky | Platí do 06/2025 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.