Pneumax - Hauptkatalog Strana 733
Nabídka komerčních zákazníků **Nejlépe prodávané z Pneumax GmbH
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Modular FRL Series 1700 Steel line Modular FRL series 1700 Steel line General Construction and operational characteristics Body, bowl and adjustment mechanism AISI 316L stainless steel Caseback regulator AISI 316L stainless steel Adjustment screw, locking nut and fastening screws AISI 316L stainless steel (stainless steel A4-70) Internal components AISI 316L stainless steel Filtering elements AISI 316 stainless steel or HDPE (High density polyethylene) Spring AISI 316 stainless steel Seals NBR (standard versions and automatic drain) NBR for low temperatures (L versions) FPM - HNBR (H versions) EPDM-FDA (EF versions) Silicone - PU (Z version) Brass, stainless steel AISI 304 and AISI 302, sintered bronze Automatic drain Acetal resin , NBR, FPM Operating Range Fluid Filtered air. No lubrication needed, if applied it shall be continuous. Inert gases. Natural gases Temperature -30°C +80°C (standard version) -5°C +150°C (high temperature H version) -50°C +80°C (low temperature L version) -5°C ÷ +70°C (automatic drain S version) -40°C ÷ +100°C (EPDM-FDA version) -60°C +80°C (low temperature version -60 °C Z) -5°C ÷ +70°C (reduced orifice automatic drain SR version) Maximum working pressure 20 bar (standard, low and high temperature versions) 16 bar (automatic drain version) 10 bar (reduced orifice automatic drain version) Instructions for installation and use Product shall be installed reducing the distance from inlet point. Check and install the device following the flow direction (clearly marked with an arrow stamped on the body). Vertical position installation with condensed exhaust tap pointing downward is recommended. Devices must be used in compliance with pressure and temperature operating range. To set the pressure there is an adjustable knob, located on the top of the device. Pneumax recommend selection of pressure regulator adjusting range option in line with client required performance The condensed exhaust action for the manual drain version shall be performed only in the absence of pressure. To discharge liquid, turn the tap clockwise until the discharge of liquid is triggered, then tighten it all the way. Maintenance Filtration elements and filter regulator are reusable through blowing and/or washing and is made of stainless steel or HDPE (high density polyethylene). To replace, remove the cup, loosen the set screw of the support and replace the filter element with a new one or refurbished one. Replace the regulator diaphragm whenever the performance is compromised or if there is a continuous discharge from the relieving hole (over-pressure exhaust). Fully discharge the adjustment spring before removing the adjustment mechanism. For other maintenance activities, due to complexity of assembly and requirement for dedicated PNEUMAX testing activities, it is strongly recommended to contact the manufacturer. Certifications available : II 2 GD c IIC II 2G Ex h IIC Gb II 2D Ex h IIIC Db : Suitable up to SIL 3 Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice : CU - TR 012 2 | 159 2 Air Service UnitS The stainless steel SS1700 air treatment series has been engineered and developed to approach specifically the OIL & GAS industry and more widely for all the severe service applications that require excellent corrosion resistance due to chemical and/or harsh environmental condition. All external and internal parts (except for the automatic drain version) are AISI 316L stainless steel material in compliance with NACE standard MR0175/ISO 15156/1. The product range includes FILTER, with filtration elements up to 3 filtration degree (5µm-20 µm-50 µm), available in AISI316 stainless steel or HDPE (high density polyethylene), and manual or automatic condensed exhaust; The PRESSURE REGULATOR is supplied with low hysteresis rolling diaphragm and an over-pressure exhaust valve (RELIEVING), available in 4 different adjustment ranges from 0 to 12 bar. As a last the FILTER REGULATOR range, which combines the features of a filter and pressure regulator into a one single device. “CLEAN PROFILE” version is available for all the sizes, featuring a glossy finish on the external surface. The over-pressure exhaust hole (RELIEVING) has a 1/8” NPT threading, and it is protected by an AISI 316 sintered filter series. Note: for CLEAN PROFILE series this is a simple unthread hole.
1106 Stránky | Platí do 06/2025 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.