Pneumax - Hauptkatalog Strana 1008
Nabídka komerčních zákazníků **Nejlépe prodávané z Pneumax GmbH
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Cable cylinders Series 1601 1600 Series, Cable driven cylinders General The cable driven cylinders work in a linear translation systems, they are very compact and can be used where a normal cylinder with a rigid rod is too cumbersome. The main characteristic of the cable cylinders is the absence of the rod which, in coming out of the end plate at the end of the stroke, doubles the total overall dimension of the cylinder. In the case of the cable cylinder, the rod is replaced by a metal rilsan-coated cable. It is connected to the piston and coming at the maximum point of stroke never exceeds the overall dimensions of the cylinder. The cable is connected to the bracket with clamps which serve also to regulate the tension. Because of the construction characteristics of this type of cylinder it must be used with much care. The cable is capable of supporting large stress due to heavy load and high speed. Unfortunately, we cannot give definitive limits of use if not in presence of masses of a few kilograms to be translated (7 - 10 for 16 and 20 - 25 for Ø 25) with speed inversely proportional to the entity of the same load (max 0,5 m/sec). This is done in a way that the load always has a mechanical stop at the end of the stroke. The magnetic piston version lengthens the overall dimensions by 50 mm; the 1200 series microcylinder sensors are used along with the clips of that series. Construction characteristics Technical characteristics Filtered air. Max. pressure:6 bar Min. and max. temperature: -5°C - +70°C Max speed: 0.5 m/sec. No lubrication needed, "Attention: Dry air must be used for application below 0°C” if applied it shall be continuous. C D Standard 86 124 Magnetic 161 182 136 174 26 B 132 13 A 111 35 Ø5,5 Ø6 A+stroke B+stroke 40 37 17 73 19 G1/8 Bore 16 30 M6 25 35 Ø5,5 15 C+stroke 29,5 22,5 D+stroke G1/8 Bore 25 30 68 1601.Ø.stroke 1601.Ø.stroke.M Version with magnetic piston 35 Ordering code 10,5 Pneumatic actuatiOn 3 NBR 80 Shore (at lip) PUR steel brass aluminium with ball bearing Piston seals Cable seal Bracket Cable clamps Pulleys anodised black aluminium anodised aluminium aluminium steel Rilsan End caps Barrel Piston Cable Cable covering Maintenance The cable is obviously the part most subject to breakage. The cylinder can be disassembled for replacement of the cable which is supplied already complete with threaded bushings to be screwed on to the piston. Once the wear of the barrel and seals has been checked, the cylinders can be reassembled by screwing on the end plates. Next, the ends of the cable are attached to the bracket by way of clamps and the tension regulated. The tension is correct when the cable is not cambered. 3 | 212 Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice
1106 Stránky | Platí do 06/2025 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.