Matador Tool Catalogue Strana 111
Nabídka komerčních zákazníků **Nejlépe prodávané z MATADOR
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Impact technology in a nutshell. Not only hot air w ith the right care. Sample installation w ith maintenance unit: M aintenance unit Oiler Filter Quick Coupler Coupler Coupler M anometer Air Hose Connecting Air Hose (ca. 30 cm) The ideal air volume. Air pressure: 6.3 bar (90 psi). Right Lubrication is the most important issue. Only w ith maintenance unit. The performance of your impact tool To reach the ideal performance of The consequent lubrication of air The reliability and durability of an depends essentially on the ideal air the impact tool the perfect air motors is absolutely required to KORCEV VQQN ECP UKIPKƂECPVN[ DG inlet pressure. volume depends on many factors: maintain full perfomance of the improved by the assembly of a motor, to prolong the life time maintenance unit. Air inlet pressures that are too high The maximum air consumption of the motor and to prevent w ill lead to accessive w ear and values for the relevant impact tool corrosion. failure of the tool after a w hile. Tools (l/min or CFM ), the recommended operating w ith too low air pressure hose sizes (inner diameter), the If you don`t use a maintenance unit ce consisting of manometer, lubrica- are usually lacking in their full OCZKOWO ƃQY TCVGU QH VJG OCKP or an additional oiler, the impact tool tor and w ater separator. performance. tenance unit and the effective should be lubricated manually capacity of the compressor must every day before use. The ideal pressure of the supplied air M ATADOR recommends to install a maintenance unit on each w orkpla- be balanced. 6JG YCVGT UGRCTCVQTU CPF ƂNVGTU w hich are integrated in our main- should be 6.3 bar (90 psi) at the air In this case decouple the impact tenance units avoid corrosion in air entrance of the air tool (also w hen The recommended hose size is tool from the quick coupler and motors and supply clean air. CKT KU ƃQYKPI 1PN[ YKVJ KFGCN indicated in the M ATADOR manuals trickle approx. 5 ml of a suitable air A high content of w ater in the air pressure the impact tool w ill and catalogues. motor oil into the hose. As a rough compressed air w ill lead to rust guide use 1-2 drops of oil per cubic inside w hich means air pressure meter compressed air. losses and a lack of performance achieve the technical properties as FGƂPGF KP VJG TGURGEVKXG OCPWCN As a rough guide please use: of the air tools. After this reconnect the impact w w w.matador.de l/ min CFM mm 100-190 4-6 6-9 195-300 7-10 13 tool w ith the air supply and run the +H PQ ƂNVGTU CTG WUGF TWUV CPF motor for a few seconds at a slow particles w ill damage or block rate in order to homogenously the motor. distribute the oil in the drive. Be a M ATADOR. | 111
328 Stránky | Platí do 12/2023 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.