Kukko puller guide Strana 13
Nabídka komerčních zákazníků **Nejlépe prodávané z Kukko
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
SEPARATING SEPARATING Mode of operation Selection of the right separating type The part to be removed is level. It is not possible to use standard puller jaws! pull For pulling tight parts such as ball bearings, roller bearings, inner rings and simliar. The sharp, wedge-shaped blades are pressed behind the parts to be removed and, in this process, push between the bearing and the seat. For pulling, the tension bolts on the pulling device (series 18) must be screwed into the separator. pull pressure 1st step: What is the diameter of the flush bearing? Normally, a separator blade is used in combination with a puller device. ? mm If the separating jaws are screwed into the pulling device the other way round, then pulling can be carried out flush and gently. Accessories: Extansions In some cases, an appropriate puller from the 20 series can be used instead of the puller bar. Accessories: long hydraulic spindles 2nd step: Choice of the separator blade 2 Seporator series 15 Separator with quick clamping pressure spindle, series 17 8-155 mm 6-250 mm TIP: One-hand operation due to quick-tension spindle It is also possible to extend the puller bar for jobs involving longer shafts. For particularly secure parts, in the larger models (from 18-2), the mechanical pressure spindle can be swapped for a hydraulic pressure spindle. More Separators 3rd step: Choice of the pulling device SEPARATING 3 pulling device series 18 SEPARATING 2 The extensive KUKKO line also supplies separators with side clamps, such as the 204 and 210 Cobra series. 50-440 mm Safety instructions for separating 4th step: Combination of the separating blade with the pulling device 4 Separator series 15 + series 18 24 4 Separator with quick clamping pressure spindle series 17 + series 18 www.KUKKO.com The adjusting nuts on the separator must be tightened in alternating and equal turns. Otherwise, the separator blade may tilt on the bolt or the thread may be damaged. www.KUKKO.com When pulling the separator blade, ensure that before the pulling device is pulled upwards the blade is firmly seated up to the stop under the part to be removed. The side bolts of the pulling device must always be spindleed into the separator blade until they stop. 25
17 Stránky | Platí do 12/2020 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.