HEWI Catalog Hardware Strana 281
Nabídka komerčních zákazníků **Nejlépe prodávané z HEWI
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Technical requirements Conditions for mounting mini Door structure Mounting is possible on both non-rebated and rebated doors. mini is recommended on residential and office building internal doors made of hollow core particleboard, with a solid particleboard insert or of a higher quality. Please note that we only recommend mounting to door elements tested by HEWI. Also, mini can be fitted to nontested door elements. However, in this case, HEWI cannot guarantee flawless mounting and permanent fitness of use. An up-to-date list of the tested door models can be found on our website at www.hewi.com/en/mini. Cut size | Lever handle The cut size (hole size) in the area of the lock follower must have a nominal size of 25 mm. Production tolerances of ± 1 mm can be levelled out by the press-in bearing. Cut size | Standard door Fräsmaß | Drücker Fräsmaß | WC Technical information Cut size | Euro cylinder or warded mortise The cut size in the area of the escutcheons (euro cylinder/ warded mortise) may be 25 x 40 mm maximum ± 1 mm. Cut size | Rose with turn knob The cut size for mounting roses with a knob must have a nominal size of 25 mm ± 1 mm Cut size | Euro cylinder or warded mortise Square spindle dimensions mini is available with a square 8 mm and square 8.5 mm, and with a lock square 7 mm for door thicknesses ranging Fräsmaß | Drücker Fräsmaß | WC-Rosette from 38.1 mm to 78 mm. Fräsmaß | PZ oder Buntbart Rosette Area of use mini fulfils the EN 1906 requirements for category of use 4. mini can be used wherever internal doors are used with low to medium frequency. mini is not suitable for use on doors with functions such as fire protection, smoke control, burglar resistance, wet-room use or radiation protection. With more than 1 million tested use cycles, an independent test institute has certified the permanently reliable quality of mini. Cut size | Rose with turn knob Design planning and advice We would be pleased to advise you in person. Please contact our support team if you have any questions. You can reach Fräsmaß | Drücker them by phone, on +49 5691 82-300, or by email, at [email protected] Fräsmaß | WC-Rosette Fräsmaß | P HEWI Hardware | 279
450 Stránky | Platí do 12/2024 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.