Ganter Norm Standard Parts - Catalogue Strana 2176
Nabídka komerčních zákazníků **Nejlépe prodávané z Ganter Norm
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
MVK Thread Locking Gluing Micro Encapsulation Precote 80 (Red) d M 5 l1 l2 ≈ 1,5 … 2,5 7,5 M IN in Nm M LB in Nm M OUT in Nm Max. insertion torque Min. breakaway torque Max. loosening torque 0,5 1 6,5 M 6 2 … 3 9 0,8 1,8 10 M 8 2,5 … 4 12 1,5 4 26 M 10 3 15 3 10 55 M 12 3,5 … 5 … 4,5 18 5 16 95 M 16 4 … 6 24 11 35 250 M 20 5 … 7,5 30 14 45 500 The torque value comply with DIN 267 Part 27. They are based on a test of a thread without preload with a nut thread of 6H at room temperature. For thread lengths l 0 < l 2, l 2 is reduced in such a way that one to two thread turns are not coated at the end of the thread. Description The principle of micro encapsulation MVK (gluing) consists of a liquid plastic material and hardener encapsulated in a thin polymer film which is embedded in a lacquer like carrier deposited in patch form an a thread. This patch dries and the component can be stored and handled in a normal manner. When fitting a bolt with this patch the two capsules will burst under the pressure and friction between the two threads. The liquid plastic material and hardener will mix leading to a chemical reaction which will harden the glue, thus giving the required thread locking. The setting of the mixture will start after 10-15 minutes. Sufficient hardness is achieved after about 30 minutes but complete setting is reached after 24 hours. Adjustment and setting process must be completed within about 5 minutes. The thread locking can be cracked by applying the M OUT torque on the thread or alternatively by heating the component over +170 °C. It is not recommended to re-use the thread. Threads, free from oil and grease give increased strength of locking action. Components treated with this process can be stored for up to 4 years. Features - Thread locking to the highest order to prevent the self loosening and component loss even under vibration. Not suitable for adjustable bolts or screws. - This security aspect may be essential for certain applications of standard parts. Stockholding of liquid glue is eliminated. - Low insertion torque - Temperature resistant from – 40 °C up to 170 °C - Excellent chemical stability Thread Locking | Page 2175
2210 Stránky | Platí do 12/2026 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.