Dynabrade - Clean Air Katalog Strana 13
Nabídka komerčních zákazníků **Nejlépe prodávané z Dynabrade Europe Sarl
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
CLEAN AIR SOLUTIONS BREAKING THE PRODUCT DOWN BY CLASS, DIVISION & GROUP Required industrial "housekeeping" best practices tend to be very specific. It is important to always understand local regulations, standards and recommendations when developing a dust abatement plan and introducing clean air solutions to a manufacturing process. The Raptor Vac® family of clean air solutions address ordinary vacuum locations and NFPA Class II, Division 1 and II locations as described below. ORDINARY LOCATION Also known as general purpose or unclassified areas, these locations are known to be free of hazardous or volatile dusts, fibers, gases, liquids and vapors. Vacuuming is the preferred method of "housekeeping" over sweeping or water wash-down. CLASS II, DIVISION 2 LOCATION One of following two situations must exist for an area to be considered a Class II, Division 2 location: 1 - Combustible non-metallic dust will not normally be in suspension in the air in quantities sufficient to produce explosive or ignitable mixtures. Dust accumulations will normally be insufficient to interfere with the normal operation of electric equipment or other apparatus. Combustible dust may be in suspension in the air as a result of infrequent malfunctioning of handling or processing equipment. 2 - Combustible dust accumulations on, or in the vicinity of the electric equipment may be sufficient to interfere with the safe dissipation of heat from electric equipment. CLASS II, DIVISION 1 LOCATION One of the following three situations must exist for an area to be considered a Class II, Division 1 location: 1 - Where combustible metallic dust is present in the air under normal operating conditions in such a quantity as to produce explosive or ignitable mixtures. This could be on a continuous, intermittent or periodic basis. 2 - Where an ignitable and/or explosive mixture could be produced if a mechanical failure or abnormal machinery operation occurs. 3 - Where electrically conductive dusts in hazardous concentrations are present. SOURCE CAPTURE Source capture clean air solutions consist of portable vacuums used in combination with an air tool or cleaning attachment. Capturing dust beyond general "housekeeping" throughout the manufacturing process promotes operator health as well as facility safety. Dynabrade source capture solutions realize enhanced operator efficiency, fewer instances of rework and extended abrasive life. USE OUR CONFIGURATOR QR CODE BELOW TO DISCOVER THE RIGHT PRODUCT FOR YOUR APPLICATION. PORTABLE VACUUMS → Clean Air Solutions 13
128 Stránky | Platí do 07/2026 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.