Dynabrade - Abrasives Katalog Strana 25
Nabídka komerčních zákazníků **Nejlépe prodávané z Dynabrade Europe Sarl
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
COATED ABRASIVE DISCS FILM & PAPER DISCS PSA & HOOK AND LOOP CONTINUED DYNACUTTM RED ALUMINUM OXIDE HEAVY WT. PAPER A GOOD choice when a heavier backing and tough abrasives are needed for sanding harder material that does not generally clog the face of the abrasive discs. 4 F E AT U R E S BENEFITS 1 Features a heavy paper backing Resistance to edge shedding on the most demanding material removal and moderate finishing applications. 2 Open Coat P graded aluminum oxide abrasive Fast removal rates and long life. DYNACUTTM WHITE SILICON CARBIDE CLOG FREE PAPER The VALUE choice for sanding materials like wood, plastic, composites, glass and for sanding sealers, primers and paint. 5 F E AT U R E S BENEFITS 1 Open coated with extremely sharp silicon carbide abrasive on a smooth B-weight paper backing Excellent for fine finishing. 2 Resin bond system Improves grain adhesion and extends disc life. 3 Clog free coating Helps to minimize build-up of sanding dust on the abrasive surface. SANDING TECHNIQUES SWIRL-FREE CHECKLIST Always START the sander ON the surface, and STOP the sander OFF the surface. When sanding keep the sander; and pad FLAT on the surface. IMPORTANT: Do not exert heavy downward force to keep the back-up pad and abrasive flat on the surface allowing the back-up pad to orbit freely over the surface. Follow a set pattern when sanding. It is suggested to pass over the surface, following a “North, South, East, West” pattern (see right), overlapping each pass 1/4 the diameter of the back-up pad and abrasive. This insures that the previous scratches are removed and that a uniform finish is achieved. Two “patterns” per sanding step are recommended. Frequently inspect abrasive for tears, folds, or build-up. When changing abrasive to proceed to the next sanding step, first inspect the condition of the abrasive that is on the sander. If any defects are noticed in that abrasive, remove it and install another piece of the same grain and sand the work surface again before proceeding on to the next sanding step. Always clear away sanding dust and abrasive debris before progressing to the next sanding step with a finer “grit” abrasive. End Start Abrasives Catalog 23
149 Stránky | Platí do 07/2026 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.