CIMCO - Main Catalogue Strana 388
Nabídka komerčních zákazníků **Produkty z katalogové stránky
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Technical appendix, numerical lisT, index, sales 1 2 3 4 5 6 7 8 9 10 11 12 hss bi-meTal hOle saw ø mm 14 16 17 19 21 22 24 25 27 29 30 32 33 35 37 38 40 41 43 44 46 48 51 52 54 57 59 mild steel 550 530 500 460 425 390 370 350 325 300 285 275 260 250 240 230 220 210 205 195 190 180 170 165 160 150 145 Va steel 300 275 250 230 210 195 185 175 160 150 145 140 135 125 120 115 110 105 100 95 95 90 85 80 80 75 75 hss bi-meTal hOle saw Cast steel 400 365 330 300 280 260 245 235 215 200 190 180 175 165 160 150 145 140 135 130 125 120 115 110 105 100 100 brass 790 730 665 600 560 520 495 470 435 400 380 360 345 330 315 300 290 280 270 260 250 240 230 220 210 200 195 aluminium 900 825 750 690 630 585 555 525 480 450 425 410 390 375 360 345 330 315 305 295 285 270 255 245 240 230 225 ø mm 60 64 65 67 70 73 76 79 83 86 89 92 95 98 102 105 108 111 114 121 127 140 146 152 mild steel 140 135 130 130 125 120 115 119 105 100 95 95 90 90 85 85 80 80 75 70 65 60 55 55 Va steel 70 70 65 65 60 60 55 55 50 50 45 45 45 45 40 40 40 40 35 35 30 30 25 25 Cast steel 95 90 85 85 80 80 75 70 70 65 65 60 60 60 55 55 55 50 50 45 40 35 35 35 brass 190 180 175 170 160 160 150 145 140 130 125 120 120 115 115 110 110 100 100 90 85 80 75 75 aluminium 220 205 200 195 185 180 170 165 155 150 145 140 135 130 125 120 115 110 105 95 90 85 80 80 13 measuRing CaTegORies CaT i TO CaT iV 14 15 16 The IEC/EN 61010-1 standard subdivides electric circuits into measuring categories CAT I to CAT IV so that measuring tools can be designed for the widely varying installation and application purposes. The measuring categories indicate in which application areas a measuring tool can be safely used. The protection of a measuring tool from a transient (=short-term, temporary) overvoltage is determined by the specification of the measurement category (overvoltage category) and the working voltage (nominal voltage to ground) e.g. CAT IV 600 V, CAT III 1,000 V. The IEC/EN 61010-1 standard subdivides measuring electric circuits into the following measuring categories: - CAT I: for measurements on electric circuits that are not directly connected to the mains. - CAT II: for measurements on electric circuits that are directly connected to the mains. - CAT III: for measurements in building installations. - CAT IV: for measurements at the source of the low-voltage installation. 17 18 19 20 21 22 23 24 25 26 • The specification of the measurement category and the maximum nominal voltage determine the protection of the measuring tool from transient (temporary) overvoltage. • These can occur due to a lightening strike in the distribution network or due to the switching on/off of large loads. • The following basic principle applies: the higher the measurement category and the higher the nominal voltage, the greater the protection of the measuring tool against transient overvoltage. • Protection against transient overvoltage to 8 kV daTa sheeT fOR led lamPs designation LED pen lamp LED work lamp LED construction site spotlight LED construction site spotlight LED construction site spotlight LED construction site spotlight article no. 11 1524 11 1522 11 1580 11 1586 11 1588 11 1590 Output – – 10 W 20 W 30 W 50 W luminous flux – – 700 Lm 1,300 Lm 2,000 Lm 2,600 Lm Protection class – IP 54 IP 65 IP 65 IP IP 388 Advice and ordering: Phone: 02191 3718-01, Fax: 02191 3718-85, E-Mail: [email protected] light angle – – 120° 120° 120° 120° Operation – – – – – – Operating time luminous colour – – 8 hrs – 4 hrs 5,500 K 5 hrs 5,500 K 3 hrs 5,500 K 3 hrs 5,500 K
420 Stránky | Platí do 12/2022 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.