AMF Catalogue Hydraulic clamping systems Strana 10
Nabídka komerčních zákazníků **Nejlépe prodávané z AMF Spannsysteme
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
screw pump No. 6901 Article no. max. operating pressure [bar] stroke volume per rev. [cm³] stroke volume total [cm³] Md max. [Nm] [g] 67819 6901-10 350 2,1 26 50 1524 67835 6901-20 350 2,1 26 50 689 Order no. Screw Pump block version and built-in version, max. operating pressure 350 bar. Weight Design: Housing from steel, hardened and burnished. Threaded spindle hardened and burnished. Screw pump no. 6901-20 is supplied with 2 grooved nuts. Oil supply via threaded port. Application: The screw pump is particularily suitable to operate small clamping fixtures. Note: 6901-10 For an enclosed circuit the following has to be considered: The hydraulic clamping elements connected to the screw pump have to be hermetically tight. Due to possible leakage of the clamping cylinders during stroke movement and the compressibility of oil (1% at 140 bar), the stroke volume of the screw pump shall be used up to 70% only. The compressibility is being increased considerabely by air content in the oil. Therefore the hydraulic system has to be carefully purged of air. An air bleed screw at the highest position is a necessity. After returing the spindle of the pump, oil must be refilled at this spot. No air pocket should arise in the hydraulic system, which cannot be purged. A precise pressure control is possible by a manometer only. An electric pressure switch enables a pressure monitoring too. A pressure limiting valve is not suitable. Operating the threaded spindle by a torque wrench is possible. However the pressure should also be checked by a gauge. For the built-in version the mounting torque has to be observed. 6901-20 6901-10 stroke Clamping pressure in relation to torque: Torque [Nm] Clamping pressure [bar] 13,5 27,0 34,0 40,5 47,5 70 140 205 275 350 oil connection 6901-20 threaded plug stroke CAD Subject to technical alterations. 10 Hydraulic clamping systems ANDREAS MAIER GmbH & Co. kg ∙ Phone: +49 711 5766-196 ∙ Web: www.amf.de
384 Stránky | Platí do 12/2025 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.
